Top 10 typical forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous accidents involving forklifts.

Case 1: The forklift cargo blocked the motorist's view, and the individual ahead might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees illegally, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not wear a safety belt and dropped from the car when it surrendered and was crushed.
Forklift operation need to focus on these matters ：.

Beginning.
1. Before starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a tons, the driver needs to first verify that the load is steady and dependable.
4. The beginning should be slow-moving and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast ought to be slanted backward. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, take care that there will be no challenges overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will cause the automobile to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique situations.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The elevation of the tons should not block the chauffeur's sight. In special circumstances, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a timely fashion, and they will certainly never operate with ailments or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the rack. .
2. It is prohibited to deal with a single fork or utilize a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and unloading products, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow and consistent. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as feasible under the load, and it must be kept in mind that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward somewhat when the lots is lowered to enable very easy placement of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, put, round or roll things. .
10. It is not permitted to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and efficient.
4. During the operation of the forklift, check whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Running up and down the incline must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move on, if they come across huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for far away driving.
3. Stand-on Electric Pallet Stacker It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roads, train crossings;.
2. Electric Forklift Truck for Warehouse Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844